linux_内核移植方法及错误

出现问题:

## Starting application at 0x30008000 ...

Uncompressing Linux.............................................................

解决方案:

setenv bootargs console=ttySAC0,115200 mem=64M ;console明令在哪暂时还没解决???

setenv

TCP cubic registered

NET: Registered protocol family 1

NET: Registered protocol family 17

Root-NFS: No NFS server available, giving up.

VFS: Unable to mount root fs via NFS, trying floppy.

VFS: Cannot open root device "<NULL>" or unknown-block(2,0)

Please append a correct "root=" boot option

Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)

解决方法：把

08.05.11、<*> RAM disk support

09.27.07、<*> Compressed ROM file system support (cramfs)

1. 问题一

　　下载内核到flash中，运行到如下即停止没有下文：

Uncompressing Linux……………………done,booting the kernel卡在这里不动了

原因分析：可能是内核的启动参数传递时没有填写正确,也可能是在linux内核中没对flash分区,还有另一可能原因是在内核编译配置时没将串口驱动勾选。

解决办法：

如果是命令参数问题，则作如下修改：注释掉arch/arm/kernel/setup.c文件中的parse_tag_cmdline()函数中的strlcpy()函数，这样就可以使用默认的CONFIG_CMDLINE了，在.config文件中它被定义为"root=/dev/mtdblock2 ro init=/linuxrc console=ttySAC0,115200"(视具体情况而定)，在内核配置文件的Boot options中填入也可。

如果是内核NAND flash分区的问题，则作如下修改：

1. 1 修改文件arch/arm/mach-s3c2410/devs.c,添加如下信息：

#include <linux/mtd/partitions.h>

#include <asm/arch/nand.h>

#include <linux/mtd/nand.h>

static struct mtd_partition partition_info[]={

{

name:"bootloader",

size:0x00040000,

offset:0,

},

{

name:"kernel",

size:0x001c0000,

offset:0x00040000,

 

},

{

name:"rootfs",

size: 0x01e00000,

offset:0x00200000,

 

},

{

name:"ext-fs1",

size: 0x01000000,

offset:0x02000000,

},

{

name:"ext-fs2",

size: 0x01000000,

offset:0x03000000,

},

};

 

//以上分区和NAND flash物理分区一样，分区不一样没试过，根据自己板子情况而定

struct s3c2410_nand_set nandset=

{

nr_partitions:5,

partitions:partition_info,

};

struct s3c2410_platform_nand s3c_nand_info=

{

tacls:0,

twrph0:30,

twrph1:0,

sets:&nandset,

nr_sets:1,

};

 

以上分区和NAND flash物理分区一样，分区不一样没试过，根据自己板子情况而定

struct s3c2410_nand_set nandset=

{

 

nr_partitions:5,

partitions:partition_info,

};

struct s3c2410_platform_nand s3c_nand_info=

{

tacls:0,

twrph0:30,

twrph1:0,

sets:&nandset,

nr_sets:1,

};

 

struct platform_device s3c_device_nand={

.name="s3c2410-nand",

.id = -1,

.num_resources = ARRAY_SIZE(s3c_nand_resources),

.resource = s3c_nand_resource, /*黑体为新加内容*/

.dev = {

.platform_data=&s3c_nand_info

}

};

 

1.2 在arch/arm/mach-s3c2410/mach-smdk2410.c文件中添加&s3c_device_nand,如下所示：

static struct platform_device * smdk2410_device[] _initdata=

{

&s3c_device_usb,

&s3c_device_lcd,

&s3c_device_wdt,

&s3c_device_i2c,

&s3c_device_iis,

&s3c_device_nand,

};

 

配置好以上内容后重新编译内核即可。

如果是串口驱动没有勾选,则一定记住将勾上如下选项:

Character devices

-> Serial Drivers下的项勾上.

2. 出现如下错误：VFS:Cannot open root device "mtdblock/2" or unknown-block(0,0)

Please append a correct "root=" boot option.

Kernel panic not syncing,VFS Unable to mount root fs on unknown-block(0,0)

原因分析：出现这种情况一般有两种情况：没有文件系统或boot options参数不正确，如我的系统文件系统为cramfs格式，存放文件系统的分区为第三个分区，启动参数为：

"noinitrd root=/dev/mtdblock2 ro init=/linuxrc console=ttySAC0,115200 rootfstype=cramfs mem=64M"

 

其中文件系统使用busybox-1.10.1制作

重新编译即可。

3. 系统启动后出现如下错误：

Kernel panic -not syncing:VFS:Unable to mount root fs on unknown-block(31,2)

或者类似的错误。

原因分析：我在这里耗了大量的时间，这种情况一般是NAND flash分区未能分正确，或者所在的分区上没有文件系统，当启动中出现类似如下信息时表明分区正确了

Scanning device for bad blocks

Creating 5 MTD partitions on "NAND 64MiB 3,3V 8-bit":

0x00000000-0x00040000 : "boot"

mtd: Giving out device 0 to boot

0x00040000-0x00200000 : "kernel"

mtd: Giving out device 1 to kernel

0x00200000-0x02000000 : "rootfs"

mtd: Giving out device 2 to rootfs

0x02000000-0x03000000 : "ext-fs1"

mtd: Giving out device 3 to ext-fs1

0x03000000-0x04000000 : "ext-fs2"

mtd: Giving out device 4 to ext-fs2

从上面看出我的文件系统放在第三个分区rootfs上，其设备号为2,启动后文件系统能挂上,如下所示

 

Reading data from NAND FLASH without ECC is not recommended

the error code is:0,name=/dev/root,fs=cramfs,flags=32769

VFS: Mounted root (cramfs filesystem) readonly.

Freeing init memory: 104K

Reading data from NAND FLASH without ECC is not recommended

init started: BusyBox v1.10.1 (2008-04-23 23:20:41 CST)

starting pid 229, tty '': '/etc/init.d/rcS'

Reading data from NAND FLASH without ECC is not recommended

the error code is:0,name=/dev/root,fs=cramfs,flags=32769

VFS: Mounted root (cramfs filesystem) readonly.

Freeing init memory: 104K

Reading data from NAND FLASH without ECC is not recommended

init started: BusyBox v1.10.1 (2008-04-23 23:20:41 CST)

starting pid 229, tty '': '/etc/init.d/rcS'

Please press Enter to activate this console.

4. 系统启动到到如下语句即停止不前，停在那里：

VFS:Mounted root (cramfs filesystem) readonly.

Freeing init memory:104

卡在这里没有下文

原因分析：系统在启用init函数时有这么一句，粗体所示

 

static int init(void * unused)

{

if(execute_command)

{

run_init_process(execute_command);

}

………………

｝

 

在这句里面出错就会没有下文

解决办法：在配置内核时少选了几句，将如下选择全选上

Floating Point emulation

->At least one emulation must be selected:

NWFPE math emulation

Support extended precision

FastFPE math emulation(EXPERIMENTAL)

5. 关于文件系统问题：在有些资料上提到在配置内核时选上devfs，如果不存在时则手动在文件里加上。但我在内核里面和busybox-1.10.1中都未加devfs支持，文件系统运行正常。在linux-2.6.14.1及以后版本中已去掉devfs。

6. linux-2.6.15.4这个版本也能成功在s3c2410上运行.

内核编译成功后，启动后出现如下提示后就停住了。。。。。。 矩阵通信网－通信.IT人的精神家园 n4}I­?QR{` t7sJ

Freeing init memory: 72K 矩阵通信网－通信.IT人的精神家园%Eq"w-?0~;{8rTm

Warning: unable to open an initial console.矩阵通信网－通信.IT人的精神家园8`9Pjq&_/N

!C+Q7f W ][0这个也是控制台console的问题，linux-2.6.13以后的内核都支持devfs，而之后版本的内核就把devfs这块去掉了，虽然还能在内核源码中找到对应的源码，你也可以把它加进内核，但是也不是太好用。2.6.13 后的版本改为支持udev了，udev这块我也没太弄懂，正在研究。-

--> Kernel Features
   --> Preemption Mode
.config 里面的 CONFIG_PREEMPT_NONE 选项决定了kernel在挂在文件系统后可不能进入shell。
-------------------------------------------------------------------------------
--> Floating point emulation
FPE_NWFPE 选项如果未选上
现象：
…………
IPv4 over IPv4 tunneling driver
TCP bic registered
NET: Registered protocol family 1
IP-Config: No network devices available.
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 4196KiB [1 disk] into ram disk... done.
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 96K
kernel 启动到这里就停止了。
-------------------------------------------------------------------------
--> Device Drivers
   --> Block devices
CONFIG_BLK_DEV_RAM选项  未选上
CONFIG_BLK_DEV_INITRD选项  未选上
现象：
………………
loop: loaded (max 8 devices)
nbd: registered device at major 43
mice: PS/2 mouse device common for all mice
IPv4 over IPv4 tunneling driver
TCP bic registered
NET: Registered protocol family 1
IP-Config: No network devices available.
Root-NFS: No NFS server available, giving up.
VFS: Unable to mount root fs via NFS, trying floppy.
VFS: Cannot open root device "ram0" or unknown-block(2,0)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)

 

1. 加载kernel后出现如下错误：

NET: Registered protocol family 1
Root-NFS: No NFS server available, giving up.
VFS: Unable to mount root fs via NFS, trying floppy.
VFS: Cannot open root device "mtdblock3" or unknown-block(2,0)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)

其中，linux command line is: "noinitrd root=/dev/mtdblock3 init=/linuxrc console=ttySAC0,115200"

解决方法，在make menuconfig 后，选中mtd支持，cramfs支持，/dev fs支持。

其中，添加/dev fs支持具体操作如下:

修改fs/Kconfig，支持启动时挂载devfs

$vim fs/ Kconfig

找到menu “Pseudo filesystem”

在其中添加：

config DEVFS_FS

bool “/dev file system support (OBSOLETE)”

default y

config DEVFS_MOUNT

bool “Automatically mount at boot”

default y

depends on DEVFS_FS

 

   之后，boot信息如下：

 

boot
Copy linux kernel from 0x00030000 to 0x30008000, size = 0x00100000 ... done
zImage magic = 0x016f2818
Setup linux parameters at 0x30000100
linux command line is: "noinitrd root=/dev/mtdblock/3 init=/linuxrc console=ttySAC0,115200"
MACH_TYPE = 193
NOW, Booting Linux......
Uncompressing Linux................................................................... done, booting the kernel.
Linux version 2.6.15.4 ([e-mail]) (gcc version 4.1.1) #5 Thu Aug 2 20:47:27 CST 2007

CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)

Machine: SMDK2410

ATAG_INITRD is deprecated; please update your bootloader.

Memory policy: ECC disabled, Data cache writeback

CPU S3C2410A (id 0x32410002)

S3C2410: core 200.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz

S3C2410 Clocks, (c) 2004 Simtec Electronics

CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on

CPU0: D VIVT write-back cache

CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets

CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets

Built 1 zonelists

Kernel command line: noinitrd root=/dev/mtdblock/3 init=/linuxrc console=ttySAC0,115200

irq: clearing subpending status 00000007

irq: clearing subpending status 00000002

PID hash table entries: 256 (order: 8, 4096 bytes)

timer tcon=00000000, tcnt a2c1, tcfg 00000200,00000000, usec 00001eb8

Console: colour dummy device 80x30

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 32MB = 32MB total

Memory: 30248KB available (1676K code, 376K data, 88K init)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

NET: Registered protocol family 16

S3C2410: Initialising architecture

S3C2410 DMA Driver, (c) 2003-2004 Simtec Electronics

DMA channel 0 at c2800000, irq 33

DMA channel 1 at c2800040, irq 34

DMA channel 2 at c2800080, irq 35

DMA channel 3 at c28000c0, irq 36

NetWinder Floating Point Emulator V0.97 (extended precision)

devfs: 2004-01-31 Richard Gooch ([e-mail])

devfs: devfs_debug: 0x0                                                                        //可以看出，已经支持devfs

devfs: boot_options: 0x1                                                                                          

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered

Console: switching to colour frame buffer device 80x25

fb0: Virtual frame buffer device, using 1024K of video memory

s3c2410-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2410

s3c2410-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2410

s3c2410-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2410

RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize

S3C24XX NAND Driver, (c) 2004 Simtec Electronics

s3c2410-nand: Tacls=1, 10ns Twrph0=4 40ns, Twrph1=1 10ns

NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V 8-bit)

NAND_ECC_NONE selected by board driver. This is not recommended !!

Scanning device for bad blocks

Creating 5 MTD partitions on "NAND 32MiB 3,3V 8-bit":

0x00000000-0x00020000 : "loader"

0x00020000-0x00030000 : "param"

0x00030000-0x001f0000 : "kernel"

0x00200000-0x00600000 : "root"

0x00600000-0x04000000 : "user"

mtd: partition "user" extends beyond the end of device "NAND 32MiB 3,3V 8-bit" -- size truncated to 0x1a00000

mice: PS/2 mouse device common for all mice

NET: Registered protocol family 2

IP route cache hash table entries: 512 (order: -1, 2048 bytes)

TCP established hash table entries: 2048 (order: 1, 8192 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

TCP bic registered

NET: Registered protocol family 1

Root-NFS: No NFS server available, giving up.

VFS: Unable to mount root fs via NFS, trying floppy.

VFS: Cannot open root device "mtdblock/3" or unknown-block(2,0)

Please append a correct "root=" boot option

Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)

 

 

 

     根据网上的一些指导，将linux_cmd_line设置为"noinitrd root=/dev/mtdblock/3 init=/linuxrc console=ttySAC0,115200"，问题

依旧。尝试了几乎所有网上的办法，问题没有得到解决。于是尝试换一个内核，下载了2.6.22的内核，按照2.6.15.4一样

配置编译了内核，当然，该版本的移植步骤有点变化，最主要的区别是，2.6.22的内核已经没有了/arch/arm/mach-s3c2410/dev.c文件，

所以，分区信息要在arch/arm/mach-s3c2410/common-smdk.c中修改static struct mtd_partition smdk_default_nand_part[] 。

boot后：

 

boot
Copy linux kernel from 0x00030000 to 0x30008000, size = 0x001d0000 ... done
zImage magic = 0x016f2818
Setup linux parameters at 0x30000100
linux command line is: "noinitrd root=/dev/mtdblock3 init=/linuxrc console=ttySAC0,115200"
MACH_TYPE = 193
NOW, Booting Linux......
Uncompressing Linux.................................................................................................. done, booting the kernel.
Linux version 2.6.22 ([e-mail]) (gcc version 4.1.1) #3 Sun Aug 5 16:00:32 CST 2007
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
Machine: SMDK2410
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2410A (id 0x32410002)
S3C2410: core 200.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists.  Total pages: 8128
Kernel command line: noinitrd root=/dev/mtdblock3 init=/linuxrc console=ttySAC0,115200
irq: clearing subpending status 00000007
irq: clearing subpending status 00000002
PID hash table entries: 128 (order: 7, 512 bytes)
timer tcon=00000000, tcnt a2c1, tcfg 00000200,00000000, usec 00001eb8
Console: colour dummy device 80x30
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 32MB = 32MB total
Memory: 29224KB available (2780K code, 309K data, 132K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
S3C2410 Power Management, (c) 2004 Simtec Electronics
S3C2410: Initialising architecture
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c2800000, irq 33
DMA channel 1 at c2800040, irq 34
DMA channel 2 at c2800080, irq 35
DMA channel 3 at c28000c0, irq 36
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
s3c2410-lcd s3c2410-lcd: no platform data for lcd, cannot attach
s3c2410-lcd: probe of s3c2410-lcd failed with error -22
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
s3c2410-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2410
s3c2410-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2410
s3c2410-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2410
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
dm9000 Ethernet Driver
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
BAST NOR-Flash Driver, (c) 2004 Simtec Electronics
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2410-nand s3c2410-nand: Tacls=1, 10ns Twrph0=4 40ns, Twrph1=1 10ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V 8-bit)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Creating 5 MTD partitions on "NAND 32MiB 3,3V 8-bit":
0x00000000-0x00020000 : "loader"
0x00020000-0x00030000 : "param"
0x00030000-0x00200000 : "kernel"
0x00200000-0x00600000 : "root"
0x00600000-0x02000000 : "user"
usbmon: debugfs is not available
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
mice: PS/2 mouse device common for all mice
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-i2c s3c2410-i2c: slave address 0x10
s3c2410-i2c s3c2410-i2c: bus frequency set to 390 KHz
s3c2410-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
TCP cubic registered
NET: Registered protocol family 1
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
VFS: Mounted root (cramfs filesystem) readonly.
Freeing init memory: 132K
Warning: unable to open an initial console.
Failed to execute /linuxrc.  Attempting defaults...

 

     看来，mtdblock3已经能认出来了，不知道上个问题是不是2.6.15.4内核本身的问题。现在的问题，好像是cramfs文件系统有问题了。

也可以理解，我下载的是在2.4内核下能成功加载的文件系统，到2.6下可能不行，看来要重新制作文件系统了。

 

    下载了1.6.1版本的buzybox，修改了makefile的arch和CROSS_COMPILER，make menuconfig，选了一些自认为需要的选项。当我选了静态编译后，编译出错，所以最后选的是动态加载，这样的话就要在编译后的添加的lib目录中将交叉编译工具的一些lib拷贝进去了。

      make install 后，生成了bin, sbin ,usr三个目录，然后

      mkdir mnt root var tmp proc boot etc lib
      mkdir /var/{lock,log,mail,run,spool}，然后mkcramfs，生成.cramfs文件，下载，boot，问题依旧，

 

drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
VFS: Mounted root (cramfs filesystem) readonly.
Freeing init memory: 132K
Warning: unable to open an initial console.
Failed to execute /linuxrc.  Attempting defaults...

        后来发现busybox生成的文件系统根目录下并没有linuxrc，所以无从执行，于是网上搜索了一下，自己编辑了一个linuxrc脚本，属性改为可执行，内容如下：

#!/bin/sh
echo "mount /etc as ramfs"
/bin/mount -n -t ramfs ramfs /etc
/bin/cp -a /mnt/etc/* /etc
echo "re-create the /etc/mtab entries"
/bin/mount -f -t cramfs -o remount,ro /dev/mtdblock/3 /
/bin/mount -f -t ramfs ramfs /etc
exec /sbin/init

 

    重新压缩下载，boot，问题依旧，真是郁闷。仔细分析了启动信息，发现虽然同样在fs/kconfig中添加了devfs的信息并且在内核编译选项中选中了

相应的内容，但是启动信息中并没有体现出来，所以怀疑devfs驱动没有加载，查看了内核的源代码，发现devfs相关的代码已经完全被删除了，看来

linux确实要和devfs断绝关系了，试着将devfs的代码拷回去，编译错误一大堆，估计要移植过去有点工作量，既然说它不好，那我也不必一定要用它

了，强扭的瓜也不甜，所以准备使用udev。

    busybox中有一个裁减的udev --〉mdev命令！选上它，又选择了一些其它的命令，重新make install busybox。发现根目录下有了linuxrc文件了！！

不是很确定到底是添加了哪些选项后出来的，也不想去试验了。赶快打包，下载，boot后，终于：

 

Copy linux kernel from 0x00030000 to 0x30008000, size = 0x001d0000 ... done
zImage magic = 0x016f2818
Setup linux parameters at 0x30000100
linux command line is: "noinitrd root=/dev/mtdblock3 init=/linuxrc console=ttySAC0,115200"
MACH_TYPE = 193
NOW, Booting Linux......
Uncompressing Linux.................................................................................................. done, booting the kernel.
Linux version 2.6.22 ([e-mail]) (gcc version 4.1.1) #3 Sun Aug 5 16:00:32 CST 2007
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
Machine: SMDK2410
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2410A (id 0x32410002)
S3C2410: core 200.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists.  Total pages: 8128
Kernel command line: noinitrd root=/dev/mtdblock3 init=/linuxrc console=ttySAC0,115200
irq: clearing subpending status 00000007
irq: clearing subpending status 00000002
PID hash table entries: 128 (order: 7, 512 bytes)
timer tcon=00000000, tcnt a2c1, tcfg 00000200,00000000, usec 00001eb8
Console: colour dummy device 80x30
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 32MB = 32MB total
Memory: 29224KB available (2780K code, 309K data, 132K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
S3C2410 Power Management, (c) 2004 Simtec Electronics
S3C2410: Initialising architecture
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c2800000, irq 33
DMA channel 1 at c2800040, irq 34
DMA channel 2 at c2800080, irq 35
DMA channel 3 at c28000c0, irq 36
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
s3c2410-lcd s3c2410-lcd: no platform data for lcd, cannot attach
s3c2410-lcd: probe of s3c2410-lcd failed with error -22
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
s3c2410-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2410
s3c2410-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2410
s3c2410-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2410
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
dm9000 Ethernet Driver
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
BAST NOR-Flash Driver, (c) 2004 Simtec Electronics
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2410-nand s3c2410-nand: Tacls=1, 10ns Twrph0=4 40ns, Twrph1=1 10ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V 8-bit)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Creating 5 MTD partitions on "NAND 32MiB 3,3V 8-bit":
0x00000000-0x00020000 : "loader"
0x00020000-0x00030000 : "param"
0x00030000-0x00200000 : "kernel"
0x00200000-0x00600000 : "root"
0x00600000-0x02000000 : "user"
usbmon: debugfs is not available
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
mice: PS/2 mouse device common for all mice
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-i2c s3c2410-i2c: slave address 0x10
s3c2410-i2c s3c2410-i2c: bus frequency set to 390 KHz
s3c2410-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
TCP cubic registered
NET: Registered protocol family 1
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
VFS: Mounted root (cramfs filesystem) readonly.
Freeing init memory: 132K

init started: BusyBox v1.6.1 (2007-08-04 22:24:34 CST) multi-call binary

starting pid 739, tty '': '/etc/init.d/rcS'

Cannot run '/etc/init.d/rcS': No such file or directory

starting pid 740, tty '': '/bin/sh'

Cannot run '/bin/sh': No such file or directory

process '-/bin/sh' (pid 740) exited. Scheduling it for restart.

starting pid 741, tty '': '/bin/sh'

Cannot run '/bin/sh': No such file or directory

process '-/bin/sh' (pid 741) exited. Scheduling it for restart.

starting pid 742, tty '': '/bin/sh'

 

 

终于有点进展了，可是新问题又出现了。重新配置busybox，发现是忘了把shell给选上了，选了ash，make install,

 

 

//////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

2440启动内核是出现

end_request: I/O error, dev mtdblock3, sector 912

Buffer I/O error on device mtdblock3, logical block 114

end_request: I/O error, dev mtdblock3, sector 912

Buffer I/O error on device mtdblock3, logical block 114

end_request: I/O error, dev mtdblock3, sector 920

Buffer I/O error on device mtdblock3, logical block 115

end_request: I/O error, dev mtdblock3, sector 920

Buffer I/O error on device mtdblock3, logical block 115

end_request: I/O error, dev mtdblock3, sector 912

Buffer I/O error on device mtdblock3, logical block 114

end_request: I/O error, dev mtdblock3, sector 920

Buffer I/O error on device mtdblock3, logical block 115

然后panic了

原因：

把drivers\mtd\nand\s3c2410.c中

chip->ecc.mode        = NAND_ECC_SOFT

改成

chip->ecc.mode        = NAND_ECC_NONE

///////////////////////////////////////////////////////////////////////////////////

Starting pid 18, console /dev/tts/0: '/bin/sh'

[2410]移植cramfs文件系统和busybox到linux2.6

2008-08-11 10:12

目前还没有成功，先把问题摆上了，挨个解决

首先是busybox的linuxrc文件的问题

按照教程上是编译完busybox后，用自己写的linxurc覆盖自动产生的这个文件

但是我的那些busybox命令好像都是链接（why？）到linuxrc的，如果替换成自己的lixnurc，全都不正确了

如果把生成的cramfs文件烧入nand中，会出现如下错误

VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing init memory: 92K
Failed to execute /linuxrc. Attempting defaults...
Kernel panic - not syncing: No init found. Try passing init= option to kernel.

但是如果不修改linuxrc文件，也会出现错误

VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing init memory: 92K
Reading data from NAND FLASH without ECC is not recommended
init started: BusyBox v1.1.3 (2008.08.11-01:57+0000) multi-call binary
Starting pid 16, console /dev/tts/0: '/etc/init.d/rcS'
Bummer,
Please press Enter to activate this console.
Starting pid 18, console /dev/tts/0: '/bin/sh'
Bummer, could not run '/bin/sh': No such file or directory
Bummer, could not run '/bin/sh': No such file or directory

头大啊该怎么办呢？

顺带说下ubuntu默认没有装zlib，make cramfs时有问题，用新立得装一下吧

将mkcramfs文件拷贝到系统的usr/bin目录下就可以使用了

对my_rootfs目录使用命令mkcramfs my_rootfs my_rootfs.cramfs生成cramfs文件系统

烧入nand闪存的第三分区，即我设定的0x400000，linux运行时可找到文件系统

==================================================

解决的第二个错误，用busybox默认的linxurc文件可以正常启动

刚才不能启动的原因是没有将ash设为默认，故没有生成/bin/sh命令

１、要这样配置：
? │ │ ? ? ? ? ? ? ? Shells ?---> ? ?
│ ? ? ? Choose your default shell (ash) ?---> ? ? ?

２、如果是这样配置的话，虽然可以生成ash，但不能生成sh：
? │ │ ? ? ? Choose your default shell (none) ?---> ? ? ? ? ? ? ? ? ? ? ? ?│ │
? │ │ ? [*] ash ?

参考如上，可惜这样不是自己的linuxrc文件，继续寻找解决方法中

VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing init memory: 92K
Reading data from NAND FLASH without ECC is not recommended
init started: BusyBox v1.1.3 (2008.08.11-02:20+0000) multi-call binary
Starting pid 16, console /dev/tts/0: '/etc/init.d/rcS'
Bummer,
Please press Enter to activate this console.
Starting pid 18, console /dev/tts/0: '/bin/sh'

BusyBox v1.1.3 (2008.08.11-02:20+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

#
# ls
bin      etc      lib      mnt      root     sys      usr
dev      home     linuxrc proc     sbin     tmp
#

==================================================

 

ECC问题，如果不把
    Device Drivers  --->
     Memory Technology Devices (MTD)  --->
        NAND Flash Device Drivers  --->
            [*]   S3C2410 NAND Hardware ECC
    去掉会出现如下的问题：
end_request: I/O error, dev mtdblock3, sector 2
EXT3-fs: unable to read superblock
end_request: I/O error, dev mtdblock3, sector 0
Buffer I/O error on device mtdblock3, logical block 0
end_request: I/O error, dev mtdblock3, sector 0
Buffer I/O error on device mtdblock3, logical block 0
end_request: I/O error, dev mtdblock3, sector 8
Buffer I/O error on device mtdblock3, logical block 1
end_request: I/O error, dev mtdblock3, sector 8
Buffer I/O error on device mtdblock3, logical block 1
end_request: I/O error, dev mtdblock3, sector 16
Buffer I/O error on device mtdblock3, logical block 2
end_request: I/O error, dev mtdblock3, sector 16
Buffer I/O error on device mtdblock3, logical block 2
end_request: I/O error, dev mtdblock3, sector 24
Buffer I/O error on device mtdblock3, logical block 3
end_request: I/O error, dev mtdblock3, sector 24
Buffer I/O error on device mtdblock3, logical block 3
end_request: I/O error, dev mtdblock3, sector 0
FAT: unable to read boot sector
VFS: Cannot open root device "mtdblock3" or unknown-block(31,3)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,3)
 另外，还要在在/linux-2.6.14.1/drivers/mtd/nand/s3c_2410.c中将
chip->eccmode = NAND_ECC_SOFT 改为 chip->eccmode = NAND_ECC_NONE;

关于initrd及RamDisk的问题
       在做2.6.14内核移植之前，我本来是想移植2.6.15的，但是出现了如是的一些问题：就是无法打开根文件系统，        终端显示的信息如下：
        VFS: Cannot open root device "mtdblock3" or unknown-block(31,3)
        Please append a correct "root=" boot option
        Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,3)
       后来改成2.6.14，同样的配置，却不会出现如上的问题。但是在这个过程中我却对RamDisk有了较好的掌握，        包括它也initrd的关系。
                Ramdisk是用来挂载根文件系统而在内存中开辟的地块区域，如果你需要你的内核支持Ramdisk，那么你需要作以下的更改：
   1). 首先，设置vivi的linux_cmd_line为：
    param set linux_cmd_line  "initrd=0x30800000,0x400000 root=/dev/ram0 init=/linuxrc         console=ttySAC0  max=00:0e:3a:aa:bb:cc"
    如果你的bootloader不可以设置启动参数，也可以在
    Boot options  --->   中的第三个选项中按回车进行设置。      
    我通过多次的测试，发现initrd=0x30800000,0x400000的作用就是在RAM中开辟一块始起地址为0x30800000,大小为    4MB的Ramdisk.
   2). 其次还要在配置内核的时候注意以下的选项：
     Device Drivers  --->
         Block devices  --->
            <*> RAM disk support                                     │ │ 
  │ │            (16)  Default number of RAM disks (NEW)                  │ │ 
  │ │            (4096) Default RAM disk size (kbytes) (NEW)              │ │ 
  │ │            [*]   Initial RAM disk (initrd) support
    这样内核就可以支持从Ramdisk启动了。其中4096KB要与上面设置的Ramdisk大小一致，这里为4MB。
    编译内核之后，这样子启动：
    net tftp 192.168.1.100 30008000 zImage
    net tftp 192.168.1.100 30800000 root_china.cramfs
    boot ram 30008000 0x12fee8      
    如果你不想用Ramdisk来挂载文件系统，直接从Flash中打开文件系统，那么在配置内核的时候，可以将RAM     disk support支持去掉。

////////////////////////////////////////////////////////////////////////////////////////////////////

Set boot params = root=1f02 init=/linuxrc console=ttyS0,115200 devfs=mount display=shp240
Uncompressing Linux.......................................................................................... done, booting the kernel.

 

2.6内核的console用的是console=ttySAC0，修改一下试试

/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////Reading data from NAND FLASH without ECC is not recommended
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing init memory: 92K
Failed to execute /linuxrc.  Attempting defaults...
Kernel panic - not syncing: No init found.  Try passing init= option to kernel.

移植了内核2.6.14.1
自己制作了文件系统cramfs，
#touch linuxrc
#chmod 777 linuxrc
#ls -al
-rwxrwxrwx  1  502 root  533 08-10 10:56 linuxrc

启动却出现这种错误。请各位大侠帮忙分析一下 ，多谢！